The common fine mist sprayer neck sizes are 18/410, 20/410, 24/410 and 28/410. Each code carries two specifications, the thread diameter and the finish series, and a sprayer only fits a bottle that matches both.
A 24 mm pump on a 24 mm bottle sounds like a match. It’s where the expensive mistakes start. A 24/410 pump is built for a finish about 16 mm tall; a 24/400 bottle is about 10 mm. Both are sold as 24 mm, and the 6 mm difference is enough to leave the gasket hanging above the rim while the collar looks almost closed.
This guide gives you the numbers behind every code: the SPI dimensions, the tolerance bands, the measuring steps and the failure patterns. It’s written for fragrance and personal care brands, contract fillers and buyers who need to sign off a drawing rather than browse a catalogue. By the end you’ll know which fine mist sprayer neck size a bottle takes, and what to send a supplier so the first sample is the right one.
If you already have a bottle in hand, send us the neck measurement and a photo and we will check it against the finish before you request a quote.
Key Takeaways
- A fine mist sprayer neck size code has two parts. In 20/410, 20 is the thread diameter and 410 is the finish series. A 20/400 pump won’t seal that bottle.
- SPI thread diameters run 17.48 to 17.88 mm for 18 mm, 19.48 to 19.89 mm for 20 mm, 23.47 to 23.88 mm for 24 mm and 27.13 to 27.64 mm for 28 mm.
- The 400, 410 and 415 series differ in height, not diameter. At 24 mm the finish is about 10 mm, 16 mm and 24 mm tall.
- Output per press is set by the pump chamber and orifice, not the neck. The same 24/410 body can deliver 0.10 ml or 0.20 ml.
- Fragrance crimp pumps have no 410 thread at all. Match the ferrule, not a neck code.
What a Fine Mist Sprayer Neck Size Code Tells You

A fine mist sprayer neck size such as 20/410 combines two specifications. The 20 is the nominal thread diameter in millimetres, measured across the outside of the threads. The 410 is the finish series, which sets the thread height, pitch and number of turns. The sprayer fits only a bottle built to the same pair.
That definition is short. The consequences are not. Both halves are nominal, so neither the round number nor the three digits tell you the exact part in front of you. You need the drawing and its tolerance.
The first number is the thread diameter
Packaging drawings call the diameter T. It is measured across the crests of the threads, the outermost edge, not across the smooth neck below them and not across the opening.
T is a range, not a point. On a 20/410 finish the SPI range is 19.48 to 19.89 mm, a window of 0.41 mm. On a high-speed capping line that window matters. A bottle at the low end and a closure at the high end can feel loose even though both are “20 mm”.
The opening is a separate dimension, listed as I. On a 24/410 bottle the minimum bore is 13.11 mm. That clearance matters for fill nozzles, for dip tubes and for any plug that enters the neck.
The second number is the finish series
The finish series sets the thread height and geometry. Three series cover almost every fine mist sprayer you will be quoted:
- 400 runs about one thread turn and sits lowest.
- 410 runs about one and a half turns and is the cosmetic standard.
- 415 runs about two turns and stands much taller.
At the same 24 mm diameter, the SPI finish heights are 9.78 to 10.54 mm for 400, 16.03 to 16.79 mm for 410 and 23.93 to 24.69 mm for 415. The diameter never changes. The height changes by roughly 6 to 8 mm per step, and that is what decides whether the gasket reaches the bottle.
Why 410 is not 4.10 mm
The three digits are a family name, not a measurement. A 410 finish is not 4.10 mm of anything, not a height, not a thread count and not a capacity. It describes a defined thread geometry that the Glass Packaging Institute and the Society of the Plastics Industry tabulated decades ago.
The practical rule is simple: quote the full code. “A 24 mm pump” is a description. “A 24/410 pump” is a specification.
Fine Mist Sprayer Neck Size Chart
The fine mist sprayer neck size chart below is the reference we use when a customer sends a bottle drawing. Values are SPI dimensions for plastic bottles, converted from the inch tables. T is the thread diameter, E the root diameter, H the finish height and I the minimum bore.
| Finish | Turns | T: thread OD (mm) | E: root OD (mm) | H: finish height (mm) | I min (mm) | Typical bottle |
|---|---|---|---|---|---|---|
| 18/410 | 1.5 | 17.48 to 17.88 | 15.34 to 15.75 | 12.90 to 13.67 | 8.26 | 10 to 50 ml |
| 18/415 | 2 | 17.48 to 17.88 | 15.34 to 15.75 | 15.29 to 16.05 | 8.26 | Tall-skirt serum and nasal packs |
| 20/400 | 1 | 19.48 to 19.89 | 17.35 to 17.75 | 9.04 to 9.80 | 10.26 | 30 to 120 ml, short neck |
| 20/410 | 1.5 | 19.48 to 19.89 | 17.35 to 17.75 | 13.69 to 14.45 | 10.26 | 30 to 120 ml |
| 20/415 | 2 | 19.48 to 19.89 | 17.35 to 17.75 | 18.46 to 19.23 | 10.26 | Tall collar, specialty pumps |
| 24/400 | 1 | 23.47 to 23.88 | 21.34 to 21.74 | 9.78 to 10.54 | 13.11 | 100 to 250 ml, short neck |
| 24/410 | 1.5 | 23.47 to 23.88 | 21.34 to 21.74 | 16.03 to 16.79 | 13.11 | 100 to 250 ml |
| 24/415 | 2 | 23.47 to 23.88 | 21.34 to 21.74 | 23.93 to 24.69 | 13.11 | Tall collar, heavy dispensers |
| 28/410 | 1.5 | 27.13 to 27.64 | 24.74 to 25.25 | 17.60 to 18.36 | 15.60 | 250 to 500 ml |
| 28/415 | 2 | 27.13 to 27.64 | 24.74 to 25.25 | 27.10 to 27.86 | 15.60 | 250 to 500 ml, high torque |
Three notes before you use it:
- The nominal size is not the actual size. A “24 mm” neck is 23.47 to 23.88 mm across the threads. Compare ranges, not labels.
- Plastic and glass differ. These are SPI values for plastic bottles. Glass follows GPI and runs slightly different dimensions. The bottle drawing and the supplier’s gauge win over any published chart, including this one.
- The 18 mm row is the least standardised. It is not on every SPI summary, and some suppliers publish a different nominal for 18/410. Confirm it on the drawing.
Two references behind the table are the Drug Plastics SPI neck finish sheet and ContaPack’s SPI table. Both are useful when a supplier questions a number.
The Four Sizes You Will Actually Be Quoted

Most fine mist sprayer neck size quotes come back with one of four finishes. The choice usually follows fill volume and actuator width, not a preference for a number.
18/410: perfume, serum and samples
18/410 is the smallest common finish, with a thread diameter of about 17.5 to 17.9 mm. It suits 10 to 50 ml bottles, including trial sizes, travel formats and pocket perfumes.
The limitation is the actuator. A small collar leaves less room for the finger pad and the nozzle housing, so the spray feels tighter than a 20/410. For a daily-use facial product, most buyers move up. For a 30 ml perfume or a serum sample, the compact look is the point.
A taller variant, 18/415, exists for pumps with a long skirt. It shares the 18 mm diameter and adds about 2 to 3 mm of finish height. If a supplier offers an 18/415 pump for a bottle you believe is 18/410, check the drawing before sampling.
20/410: the cosmetic default
20/410 is the workhorse. Face mists, toners, setting sprays and small treatment products overwhelmingly use it, usually on 30 to 120 ml bottles. A 20-410 finger sprayer is a standard stock component in this size.
It is also where the 400 trap is most common. 20/400 and 20/410 share a thread diameter of 19.48 to 19.89 mm. Their heights are 9.04 to 9.80 mm against 13.69 to 14.45 mm. A 20/410 sprayer on a 20/400 bottle screws down until the skirt meets the shoulder, and the gasket never compresses.
24/410: body, hair and hand care
24/410 covers 100 to 250 ml formats and most body mists, hair products and hand sanitisers. It gives the widest actuator, the easiest press and the largest choice of stock sprayers.
Because 24 mm is so common, it attracts the most confusion. A 24/400 bottle and a 24/415 bottle both start with 24, and neither accepts a 24/410 sprayer. If a quotation says “24 mm sprayer”, ask for the full finish before you compare prices.
28/410: room and linen sprays
28/410 usually suits 250 to 500 ml bottles and higher output formats. Room sprays, linen mists and larger body products use it, often with a trigger or a high-output actuator rather than a fine mist.
Above 500 ml, a hand-held fine mist becomes impractical. The market moves to trigger sprayers with different economics and a different neck standard.
When 415 is the right call
Choose 415 when the bottle is already tooled for it, or when the design calls for a tall collar that hides the neck. Some heavy dispensers and high-viscosity products use the extra thread engagement.
Do not choose 415 because it sounds stronger. For a cosmetic fine mist sprayer, 410 has the widest component choice and the shortest sampling route. If you are specifying a new bottle, 24/410 or 28/410 is the safer default.
410 vs 415 vs 400: The Compatibility Trap
Most leaks blamed on a “bad sprayer” start with a finish mismatch. The diameter passes a caliper check, the parts look right, and the seal fails later.
Thread turns and bottoming out
A 400 finish engages about one turn, a 410 about one and a half, and a 415 about two. More turns mean a taller finish and a longer thread engagement.
Put a 415 sprayer on a 410 bottle and the skirt bottoms out on the shoulder before the gasket compresses. The collar may look closed, but the seal is air. Put a 410 sprayer on a 415 bottle and the neck stands proud of the skirt, so the closure engages the wrong part of the thread. Both pairings can pass a quick visual check and fail a leak test.
The 24/400 case
The 24/400 to 24/410 swap is the most expensive version of this mistake. Both measure 23.47 to 23.88 mm across the threads. Their heights are 9.78 to 10.54 mm and 16.03 to 16.79 mm.
That is roughly 6 mm of difference. On a filling line it looks like a pump that will not seat. If the capping torque is high enough, the machine forces the skirt down and cracks it. The failure then appears as a split collar on a filled unit rather than a loose pump on an empty one.
When 415 is right, and when it is only available
415 is a valid engineering choice. It gives more thread engagement, a taller sealing collar and a different look. It is also less common in cosmetics, so fewer stock sprayers exist and sampling can take longer.
If a supplier offers only 415, do not accept it as a substitute for 410. Change the bottle drawing to 415 and qualify the closure as a pair, or find a 410 supply. Mixing the two is not a compromise; it is a defect.
How to Measure a Bottle Neck in Three Steps
Measuring a fine mist sprayer neck size takes calipers, the bottle and five minutes. A catalogue photo is not a measurement.
Step 1: Measure T across the threads
Close the caliper jaws across the outside of the thread crests, not across the smooth band below the threads. Take three readings about 120 degrees apart and use the largest.
Read the result against the chart:
| Reading | Finish diameter |
|---|---|
| 17.48 to 17.88 mm | 18 mm |
| 19.48 to 19.89 mm | 20 mm |
| 23.47 to 23.88 mm | 24 mm |
| 27.13 to 27.64 mm | 28 mm |
A reading between two bands is a warning. It can mean an oval neck, a worn mould or a caliper placed on a burr. Measure again at a different height before you choose a sprayer.
Step 2: Measure H and count the turns
Measure from the top edge of the finish down to the shoulder, parallel to the centre line. Then count the thread starts from the top.
On a 24 mm neck, a height near 10 mm points to 400, near 16 mm to 410 and near 24 mm to 415. The turns confirm it: about one for 400, one and a half for 410, two for 415.
Height is the measurement most buyers skip, and it is the one that predicts a leak. If you only have a diameter, you have half a specification.
Step 3: Cross-check the tolerance and the drawing
Compare your reading with the bottle drawing, not just the nominal code. The drawing carries T, E, H and I with tolerances. A bottle outside the T tolerance will not seal reliably even with the correct closure code.
For reference, the ISBT SP410 drawing gives a T tolerance of plus or minus 0.20 mm and an H tolerance of plus or minus 0.38 mm. Fomalpack’s neck finish guide reproduces those figures and explains the measurement points.
If you are matching a pump rather than a sprayer, the pump-side specifications cover the closure dimensions in more detail. For a full selection framework beyond neck size, see the complete fine mist sprayer selection guide.
Matching Fine Mist Sprayer Neck Size to Output, Dip Tube and Capacity
The neck size decides fit. It doesn’t decide dose. Treating the two as one gives you a sprayer that seals but dispenses the wrong amount.
| Finish | Typical output range | Typical capacity | What sets the output |
|---|---|---|---|
| 18/410 | 0.08 to 0.14 ml | 10 to 50 ml | Pump chamber and orifice |
| 20/410 | 0.10 to 0.16 ml | 30 to 120 ml | Pump chamber and orifice |
| 24/410 | 0.12 to 0.20 ml | 100 to 250 ml | Pump chamber and orifice |
| 28/410 | 0.15 to 0.25 ml | 250 to 500 ml | Pump chamber and actuator |
Those ranges are typical catalogue bands, not a rule. Output is a pump property. The same 24/410 body can be built at 0.10 ml or 0.20 ml by changing the chamber and the insert. HCC Packaging, for example, lists confirmed fine mist options of 0.12, 0.18 and 0.20 cc across its 18, 20 and 24 mm necks.
The dose also changes how long a bottle lasts. A 100 ml body mist at 0.20 ml per press gives about 500 applications, while 0.30 ml gives about 333. A 50 ml toner at 0.12 ml gives roughly 417 presses.
If the label promises a number of uses, check it against the pump, not the fill volume alone.
Dip tube length follows the bottle
The dip tube should end 3 to 6 mm above the inside base of the bottle. Too short and the pump draws air before the bottle is empty. Too long and the tube bows, then pushes the sprayer up or springs back after each press.
Measure from the sealing rim inside the neck to the base, then trim. On an asymmetrical bottle, measure at the lowest point. A tube cut to the bottle’s outer height will be wrong on almost every shoulder shape.
Why a Correct Code Still Leaks
Matching the fine mist sprayer neck size removes the most common failure. It doesn’t guarantee a seal. These are the patterns worth checking before a production run.
| Symptom | Most likely cause | Fix |
|---|---|---|
| Sprayer sits high with a visible gap | Finish series mismatch, such as 415 on 410 | Match H, not just the diameter |
| Leak at the collar after capping | Gasket compressed past spec or wrong gasket material | Check capping torque and formula compatibility |
| Sprayer spins freely | Thread diameter mismatch | Re-measure T and confirm the full code |
| Seepage at the shoulder after transit | Dip tube too long and bowing | Trim to 3 to 6 mm above the base |
| Pump slow to prime | Tube too short or formula too viscous | Check tube length and viscosity |
| Cross-threaded skirt | Closure forced onto a mismatched finish | Fit a sample by hand before the line starts |
Gasket material is a chemical decision. An alcohol-heavy fragrance and a natural oil blend can need different elastomers. Capping torque is a machine setting that drifts, so a batch that passed at the start of a shift can fail at the end.
If a sprayer has already failed in the field, the fine mist sprayer troubleshooting guide walks through the diagnosis step by step.
Crimp vs Screw: When Neck Size Does Not Apply

Not every fragrance sprayer screws on. A crimp pump seals against a glass neck with a metal ferrule that a crimping tool presses into place. There’s no thread, so there’s no 410 code.
| Crimp sprayer | Screw sprayer | |
|---|---|---|
| How it attaches | Aluminium ferrule crimped over the glass neck | Threaded closure on an SPI finish |
| Fit is specified by | Ferrule diameter and collar height | Full neck code such as 24/410 |
| Common use | Perfume, fragrance samples, tamper evidence | Face mist, body mist, hair care, refill packs |
| Consumer can remove it | No | Yes |
Fragrance bottles commonly use 13, 15, 18 and 20 mm ferrules. A brand that asks for a “24/410 perfume sprayer” for a crimp-neck flacon has described a part that doesn’t exist. No screw sprayer will fit that bottle, and no amount of sampling will create a thread.
The correct request is a crimp pump with the matching ferrule diameter and collar height. Our perfume bottle neck sizes page covers the crimp side, including collar and ferrule measurement. The fine mist spray pump page explains how the two closure families differ.
What to Send for an Accurate Quote
A supplier can confirm a fine mist sprayer neck size from a good drawing. Without one, both sides guess.
Send these seven items with an RFQ:
- The bottle drawing, with T, E, H and I dimensions and tolerances.
- A physical bottle or a clear photo with a ruler in frame.
- The target output in millilitres or cc per press.
- The formula type and approximate viscosity, plus alcohol or oil content.
- The fill volume and the bottle’s internal height.
- The quantity per SKU, colour and decoration plan.
- The target market, because labelling and child-resistance rules vary.
With those items, a supplier can match the sprayer, cut the dip tube and quote without a second sampling round. Production runs take 4 to 6 weeks once an order is confirmed. Our MOQ is quoted per project rather than published as a single number, because it depends on the sprayer, the decoration and the bottle.
If you are buying at volume, the wholesale fine mist sprayers guide covers RFQ structure, tooling and landed cost.
FAQ
What does 20/410 mean on a fine mist sprayer?
20 is the thread diameter in millimetres, measured across the outside of the threads. 410 is the finish series, which sets the thread height and geometry. The sprayer fits a bottle with the same 20/410 finish, not any bottle with a 20 mm neck.
Is 20/410 the same as 20/400?
No. They share a thread diameter, but the 410 finish is 13.69 to 14.45 mm tall and the 400 finish is 9.04 to 9.80 mm. A 20/410 sprayer on a 20/400 bottle bottoms out before the gasket compresses.
Can I use a 24/410 sprayer on a 24/415 bottle?
No. The diameter matches and the height does not. A 24/410 pump on a 24/415 neck engages the wrong part of the thread, and the seal cannot be trusted. Match the complete code.
How much does a fine mist sprayer dispense per spray?
Most cosmetic fine mist sprayers deliver 0.08 to 0.25 ml per stroke. Fragrance sits at the low end and body mist at the high end. The neck size doesn’t set this figure; the pump chamber and orifice do.
How long should the dip tube be?
Long enough to end 3 to 6 mm above the inside base of the bottle without touching it. If the supplier doesn’t offer your length, the tube is usually trimmed at filling rather than ordered to size.
What neck size do most face mists use?
20/410 is the most common for face mists and toners in 30 to 120 ml bottles. Larger body mists usually move to 24/410, and room sprays to 28/410.
Conclusion
The fine mist sprayer neck size is a compatibility promise, and both halves of the code have to be honoured. Measure T, measure H, count the turns, and compare the result with the bottle drawing. A caliper check on the diameter alone will pass a 24/400 bottle as a 24/410 and send the error to the filling line.
The four sizes that matter are 18/410, 20/410, 24/410 and 28/410. Output, dip tube and capacity are separate decisions that follow the fit. Crimp-neck fragrance bottles skip the thread system entirely, so match a ferrule there instead.
If you have a bottle drawing or a sample, request a quote and send the neck dimensions with it. We will confirm the finish against the drawing, recommend a sprayer and cut the dip tube to your bottle before you commit to production. For the wider picture, start with the complete fine mist sprayer selection guide.





